Plumbing for Beginners: The Essentials for Bathtub Installation
Plumbing for Beginners: The Essentials for Bathtub Installation
Blog Article
How do you actually feel in regards to Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't exactly rocket science, however it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bathtub with a new one is also a reasonably hard job. If the old bathtub is easily available, the job can relocate quickly; if you need to open up a wall surface to eliminate the old tub and also position the new bath tub, the task is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have certified yourself for the work as well as are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed task, it is better to take into consideration using one before you begin. Possibilities are you may need an expert plumber to make tube links.
This article will certainly assist you install a new tub in your shower room if you have actually currently gotten a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your devices and material checklist need to consist of the following:
Getting ready for the Installment
To start with, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the tub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will come from the pipelines. When the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Utilizing the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny factors.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub until the level reviews degree.
To install faucets, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Activate the supply of water as well as inspect all joints as well as new pipework for leaks and also tighten them if required. Fill the bath tub as well as additionally examine the overflow outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub needs to wait up until the bath tub has been utilized at the very least once as this will settle it into its last position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers are in place in between the faucet and also the sink. Protect the faucet in place with the supplier provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, causing complications with wetness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water before securing, to permit the movement experienced when the bathtub remains in usage. The sealer can fracture rather early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that editorial about How to Install a Bathtub from an acquaintance on our other website. Appreciated our blog posting? Please share it. Let someone else find it. I am grateful for your time. Don't hesitate to stop by our website back soon.
24/7 support? Call. Report this page